NibblerBOT Feeds Speeds - Revision history

Larry: Added new entry.

2026-04-29T17:26:25Z

Added new entry.

← Older revision		Revision as of 17:26, 29 April 2026
Line 1:		Line 1:
	This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT. Everyone should be able to directly add their own experiences, please fill out rows completely if dropping in a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on ~~Mattermost~~ and I'll add them.		This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT. Everyone should be able to directly add their own experiences, please fill out rows completely if dropping in a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on KM chat and I'll add them.

	For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.		For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.
Line 12:		Line 12:
	!Result		!Result
	!Operator		!Operator
			!Notes
	\|-		\|-
	\|Texas Ebony		\|Texas Ebony
Line 21:		Line 22:
	\|Good		\|Good
	\|@doceck		\|@doceck
			\|
	\|-		\|-
	\|Texas Ebony		\|Texas Ebony
Line 30:		Line 32:
	\|Good		\|Good
	\|@doceck		\|@doceck
			\|
	\|-		\|-
	\|MDF		\|MDF
Line 39:		Line 42:
	\|Good		\|Good
	\|@doceck		\|@doceck
			\|
			\|-
			\|Oak
			\|61
			\|14K
			\|250
			\|250
			\|Surfacing
			\|Good
			\|@mattmestayer
			\|Cookie surfacing, .10 step down, 50% stepover for roughing and .05 step down & 20% stepover for finishing.
	\|}		\|}

DocEck: row entry for MDF tool 40

2026-03-16T21:02:48Z

row entry for MDF tool 40

← Older revision		Revision as of 21:02, 16 March 2026
Line 20:		Line 20:
	\|Surfacing		\|Surfacing
	\|Good		\|Good
	\|@~~docek~~		\|@doceck
	\|-		\|-
	\|Texas Ebony		\|Texas Ebony
Line 29:		Line 29:
	\|Profile		\|Profile
	\|Good		\|Good
	\|@~~docek~~		\|@doceck
	\|-		\|-
	\|		\|MDF
	\|		\|40
	\|		\|18k
	\|		\|80
	\|		\|30
	\|		\|Pocket and Profile
	\|		\|Good
	\|		\|@doceck
	\|}		\|}

larry at 11:39, 15 March 2026

2026-03-15T11:39:17Z

← Older revision		Revision as of 11:39, 15 March 2026
Line 1:		Line 1:
	This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT ~~to date~~. ~~EVERYONE~~ should be able to add their own experiences, please fill out rows completely if ~~adding~~ a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.		This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT. Everyone should be able to directly add their own experiences, please fill out rows completely if dropping in a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.

	For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.		For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.

larry at 21:46, 14 March 2026

2026-03-14T21:46:02Z

← Older revision		Revision as of 21:46, 14 March 2026
Line 1:		Line 1:
	This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.		This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.

	For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that ~~performs~~ a similar operation.		For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.
	{\| class="wikitable"		{\| class="wikitable"
	\|+		\|+

larry at 21:30, 14 March 2026

2026-03-14T21:30:36Z

← Older revision		Revision as of 21:30, 14 March 2026
Line 1:		Line 1:
	This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry and I'll add them.		This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.

	For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that performs a similar operation.		For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that performs a similar operation.

larry at 21:29, 14 March 2026

2026-03-14T21:29:20Z

← Older revision		Revision as of 21:29, 14 March 2026
Line 1:		Line 1:
	This page is meant to ~~accumulate~~ real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result.		This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry and I'll add them.


			For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that performs a similar operation.
	{\| class="wikitable"		{\| class="wikitable"
	\|+		\|+

larry: Creating Page

2026-03-14T21:16:52Z

Creating Page

New page

This page is meant to accumulate real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result.

{| class="wikitable"
|+
!Material
!Tool#
!Speed
!H Feed (IPM)
!V Feed (IPM)
!Operation
!Result
!Operator
|-
|Texas Ebony
|70
|14K
|80
|80
|Surfacing
|Good
|@docek
|-
|Texas Ebony
|31
|18K
|100
|100
|Profile
|Good
|@docek
|-
|
|
|
|
|
|
|
|
|}