NibblerBOT Feeds Speeds: Difference between revisions

From Knox Makers Wiki
← Older edit
VisualWikitext
larry (talk | contribs)
63 edits
mNo edit summary
Larry (talk | contribs)
47 edits
Updated table with new data
 
(3 intermediate revisions by 3 users not shown)
Line 1: Line 1:
This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT to date. EVERYONE should be able to add their own experiences, please fill out rows completely if adding a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on Mattermost and I'll add them.
This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT. Everyone should be able to directly add their own experiences, please fill out rows completely if dropping in a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on KM chat and I'll add them.


For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.
For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.
Line 6: Line 6:
!Material
!Material
!Tool#
!Tool#
!Tool
!Speed
!Speed
!H Feed (IPM)
!H Feed (IPM)
Line 12: Line 13:
!Result
!Result
!Operator
!Operator
!Notes
|-
|-
|Texas Ebony
|Texas Ebony
|70
|70
|1-1/4" Bowl & Tray
|14K
|14K
|80
|80
Line 20: Line 23:
|Surfacing
|Surfacing
|Good
|Good
|@docek
|@doceck
|
|-
|-
|Texas Ebony
|Texas Ebony
|31
|31
|1/4" 2FL Spiral Down Cut
|18K
|18K
|100
|100
Line 29: Line 34:
|Profile
|Profile
|Good
|Good
|@docek
|@doceck
|
|-
|-
|MDF
|40
|1/4" 2FL COMP
|18k
|80
|30
|Pocket and Profile
|Good
|@doceck
|
|
|-
|Oak
|61
|2" 3FL Spoil Board
|14K
|250
|250
|Surfacing
|Good
|@mattmestayer
|Cookie surfacing, .10 step down, 50% stepover for roughing and .05 step down & 20% stepover for finishing.
|-
|3/4 Plywood
|32
|1/2" 2FL Spiral Down Cut
|16K
|200
|200
|Pocket Shape (dado and rabbet ops)
|Good
|@larry
|Started out at 180 feed, dynamically up that to 210 and was humming along.
|-
|3/4 Plywood
|81
|1/2" Point Roundover
|16K
|120
|120
|Roundover
|Good
|@larry
|Offsetting both height & XY by .02" seemed to work well.
|-
|3/4 Plywood
|31
|1/4" 2FL Spiral Down Cut
|18K
|120
|120
|Profile
|Good
|@larry
|
|
|
|-
|
|3/4 Plywood
|
|41
|
|1/4" 2FL COMP
|
|18K
|120
|120
|Profile (finish)
|Good
|@larry
|
|
|}
|}

Latest revision as of 12:27, 2 August 2026

This page is meant to document real world experience on Feeds & Speeds used on NibblerBOT. Everyone should be able to directly add their own experiences, please fill out rows completely if dropping in a new result. If you tried an existing combination and it didn't perform as the original Operator noted then add you experience under theirs, do not delete the original note! If you would prefer to have the info added for you feel free to message the details to @larry on KM chat and I'll add them.

For Result, please include something to indicate how the actual operation performed vs. the expected. This can and should be as verbose as necessary to convey what you'd suggest changing to make the operation better. For something that ran as expected 'Good' or similar is fine. If perhaps the feeds were a little too fast then perhaps 'Slow down V and H Feed appx 20%'. Spindle speed too slow? Maybe something like 'Increase spindle speed 30%'. Be descriptive and remember, the goal is to inform the next person that does a similar operation on how to improve the performance if changes are needed.

Material Tool# Tool Speed H Feed (IPM) V Feed (IPM) Operation Result Operator Notes
Texas Ebony 70 1-1/4" Bowl & Tray 14K 80 80 Surfacing Good @doceck
Texas Ebony 31 1/4" 2FL Spiral Down Cut 18K 100 100 Profile Good @doceck
MDF 40 1/4" 2FL COMP 18k 80 30 Pocket and Profile Good @doceck
Oak 61 2" 3FL Spoil Board 14K 250 250 Surfacing Good @mattmestayer Cookie surfacing, .10 step down, 50% stepover for roughing and .05 step down & 20% stepover for finishing.
3/4 Plywood 32 1/2" 2FL Spiral Down Cut 16K 200 200 Pocket Shape (dado and rabbet ops) Good @larry Started out at 180 feed, dynamically up that to 210 and was humming along.
3/4 Plywood 81 1/2" Point Roundover 16K 120 120 Roundover Good @larry Offsetting both height & XY by .02" seemed to work well.
3/4 Plywood 31 1/4" 2FL Spiral Down Cut 18K 120 120 Profile Good @larry
3/4 Plywood 41 1/4" 2FL COMP 18K 120 120 Profile (finish) Good @larry
Retrieved from "https://wiki.knoxmakers.org/index.php?title=NibblerBOT_Feeds_Speeds&oldid=5430"