Laser Cutter: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| Line 51: | Line 51: | ||
==Buildlog.net Interface Board== | ==Buildlog.net Interface Board== | ||
{| | {| class="wikitable" style="text-align: center;" | ||
|- Header 1 | | |Designator||Qty||Description||Part Number||Supplier | ||
|- | |- | ||
|C1,C2,C12-C16||7||0.1uF 50V 20% Ceramic Cap||Kemet C410C104M5U5TA7200|| | |||
|- | |||
|C3-C5||3||220uF 25V Electrolytic Cap||Panasonic ECE-A1AKA221|| | |||
|- | |||
|C6-C11||6||100pF 100V 5% Ceramic Cap||AVX SA102A101JAR|| | |||
|- | |||
|CR1-CR3||3||Diode, 1N4148||Generic|| | |||
|- | |||
|J1||1||Connector, D 25 Pin Male 90 Deg||FCI 10090097-P254VLF|| | |||
|- | |||
|J2||1||Connector, D 9 Female|| || | |||
|- | |||
|J3||1||Connector, D 9 Male|| || | |||
|- | |||
|J4||1||Connector, RJ45 Shielded||Stewart SS-6488S-A-NF|| | |||
|- | |||
|J5||1||Connector, DC Power|| || | |||
|- | |||
|JP1,JP2,JP3||3||Connector, Male Header 3pos||Generic|| | |||
|- | |||
|K1||1||Relay||Panasonic TQ2H-5V|| | |||
|- | |||
|Q1||1||Transistor||Motorola MPS2222A|| | |||
|- | |||
|Q2,C3||2||MOSFET||Vishay IRL520|| | |||
|- | |||
|R1-R4,R10,R12,R14,R17,R18,R21,R22,R24,R26||13||Resistor, 10K, 1/4W||Generic|| | |||
|- | |||
|R5,R6,R7,R8||4||Resistor, 100R, 1/4W||Generic|| | |||
|- | |||
|R9,R11,R13||3||Resistor, 1K, 1/4W||Generic|| | |||
|- | |||
|R15,R16,R19,R20,R23,R25||6||Resistor 10 Ohm, 1/4W, Metal Film||Generic|| | |||
|- | |||
|RP1||1||Resistor Array 10K x 9|| || | |||
|- | |||
|S1,S2,S3||3||Hex Rotary Switch||Copal S1011|| | |||
|- | |||
|TB1,TB2,TB3,TB5||3||Terminal block 5mm x 4, Pluggable|| || | |||
|- | |||
|TB4||1||Terminal block 5mm x 4|| || | |||
|- | |||
|TB4||1||Terminal block,5mm x 3, Pluggable|| || | |||
|- | |||
|TB8||1||Terminal block 5mm x 3|| || | |||
|- | |||
|U1||1||Power Supply 5V DC/DC||Murata OKI-78SR-5/1.5-W36-C|| | |||
|- | |||
|U2||1||Power Supply 3.3V DC/DC||Microchip MCP1700-3302E/TO|| | |||
|- | |||
|U3,U4,U5||3||Stepper Driver||Pololu A4983 or A4988|| | |||
|- | |||
|U6||1||Schmitt Trigger Non-Inverting||NXP 74HC7014|| | |||
|- | |||
|B1||1||50mm Blower, 5V||Sunon KDE0505PFV1.11.MS.A.GN|| | |||
|- | |||
|Terminal Block Plug ||3||4C For stepper motors|| || | |||
|- | |||
|Terminal Block Plug||1||3C For water connection|| || | |||
|- | |||
|Power Connector||1||For 24VDC power input CUI|| || | |||
|- | |||
|Jumper||3||0.1” Jumper Cap||Generic|| | |||
|- | |||
|Standoffs||4||For blower||McMaster|| | |||
|- | |||
|Screws||4||PHMS #4-40 x 2.5|| || | |||
|- | |||
|Nuts||4||#4-40 Nylon Locking||Generic|| | |||
|- | |||
|} | |} | ||
Revision as of 00:16, 12 November 2012
Theory / General Info
Laser
- Good notes on controlling the intensity of the laser with PWM - Laser Power Settings Via PWM Can Fool You
Optics
Linear Motion
Electronics
- Potential arduino shield to use with LasaurGrbl - LasaurShield
Software
- Potential controller software based on Grbl- LasaurGrbl
- Software to run on Mac/PC to send G-code to LasaurGrbl - LasaurApp
Build Notes
- The laser cutter being built is based around the laser cutter on Buildlog.net
- Another good reference is Lasersaur
To Do List
Buy/build shaft couplers for y-axis--Andronicus 22:46, 24 October 2012 (EDT)- Buy honeycomb surface
Buy large z-axis gear and timing belt--Andronicus 18:31, 20 October 2012 (EDT)- Buy cable carriers
Buy Pololu motor drivers--Andronicus 00:50, 20 October 2012 (EDT)BuyGet Pololu heat sinks from Brian--Andronicus 15:53, 10 November 2012 (EST)- Specify limit switches
- Buy limit switches
Cut 1/4" aluminum rod stock to 12" & 14" sections for y-axis shafts--Andronicus 18:31, 20 October 2012 (EDT)- Machine air assist nozzle
- Build roll around table -- In progress (Mike)
- Assemble x & y-axis pulleys
- Figure out permanent z-axis electronics
- Buy outlets and terminal blocks
- Buy a flow indicator
- Post laser power supply information
- Laser test setup???
- Paint
- Build doors
- Mount fire extinguisher
- Mount push bar
- Determine electronics setup
Parallel Port Option: Interface board from buildlog.net--Andronicus 22:46, 24 October 2012 (EDT)- Procure electronics components for interface board
- Parallel port cabling
- Bring in computer
- Bring in old RAM
- USB Option: Lasersaur Arduino Shield -- ON HOLD
Buildlog.net Interface Board
| Designator | Qty | Description | Part Number | Supplier |
| C1,C2,C12-C16 | 7 | 0.1uF 50V 20% Ceramic Cap | Kemet C410C104M5U5TA7200 | |
| C3-C5 | 3 | 220uF 25V Electrolytic Cap | Panasonic ECE-A1AKA221 | |
| C6-C11 | 6 | 100pF 100V 5% Ceramic Cap | AVX SA102A101JAR | |
| CR1-CR3 | 3 | Diode, 1N4148 | Generic | |
| J1 | 1 | Connector, D 25 Pin Male 90 Deg | FCI 10090097-P254VLF | |
| J2 | 1 | Connector, D 9 Female | ||
| J3 | 1 | Connector, D 9 Male | ||
| J4 | 1 | Connector, RJ45 Shielded | Stewart SS-6488S-A-NF | |
| J5 | 1 | Connector, DC Power | ||
| JP1,JP2,JP3 | 3 | Connector, Male Header 3pos | Generic | |
| K1 | 1 | Relay | Panasonic TQ2H-5V | |
| Q1 | 1 | Transistor | Motorola MPS2222A | |
| Q2,C3 | 2 | MOSFET | Vishay IRL520 | |
| R1-R4,R10,R12,R14,R17,R18,R21,R22,R24,R26 | 13 | Resistor, 10K, 1/4W | Generic | |
| R5,R6,R7,R8 | 4 | Resistor, 100R, 1/4W | Generic | |
| R9,R11,R13 | 3 | Resistor, 1K, 1/4W | Generic | |
| R15,R16,R19,R20,R23,R25 | 6 | Resistor 10 Ohm, 1/4W, Metal Film | Generic | |
| RP1 | 1 | Resistor Array 10K x 9 | ||
| S1,S2,S3 | 3 | Hex Rotary Switch | Copal S1011 | |
| TB1,TB2,TB3,TB5 | 3 | Terminal block 5mm x 4, Pluggable | ||
| TB4 | 1 | Terminal block 5mm x 4 | ||
| TB4 | 1 | Terminal block,5mm x 3, Pluggable | ||
| TB8 | 1 | Terminal block 5mm x 3 | ||
| U1 | 1 | Power Supply 5V DC/DC | Murata OKI-78SR-5/1.5-W36-C | |
| U2 | 1 | Power Supply 3.3V DC/DC | Microchip MCP1700-3302E/TO | |
| U3,U4,U5 | 3 | Stepper Driver | Pololu A4983 or A4988 | |
| U6 | 1 | Schmitt Trigger Non-Inverting | NXP 74HC7014 | |
| B1 | 1 | 50mm Blower, 5V | Sunon KDE0505PFV1.11.MS.A.GN | |
| Terminal Block Plug | 3 | 4C For stepper motors | ||
| Terminal Block Plug | 1 | 3C For water connection | ||
| Power Connector | 1 | For 24VDC power input CUI | ||
| Jumper | 3 | 0.1” Jumper Cap | Generic | |
| Standoffs | 4 | For blower | McMaster | |
| Screws | 4 | PHMS #4-40 x 2.5 | ||
| Nuts | 4 | #4-40 Nylon Locking | Generic |