Machining: Difference between revisions
No edit summary |
No edit summary |
||
| Line 12: | Line 12: | ||
We'll mount the Mini-lathe to this toolbox. The existing medical rolling cabinet is too large and bulky, drawers on both ends confusing, and it's too low to the ground. $184.00 + Tax | We'll mount the Mini-lathe to this toolbox. The existing medical rolling cabinet is too large and bulky, drawers on both ends confusing, and it's too low to the ground. $184.00 + Tax | ||
* <s>[http://www.utoole.com/10-Rotary-Table-Combo_p_133.html 10" Rotary Table with Tail Stock & Index Plates]</s> | * <s>[http://www.utoole.com/10-Rotary-Table-Combo_p_133.html 10" Rotary Table with Tail Stock & Index Plates]</s> | ||
* [http://www.utoole.com/The-Adapter-and-3-Jaw-Chuck-for-Mounting-on-a-10-Rotary-Table_p_52.html 8" 3 Jaw Chuck and adapter plate for Rotary Table] | * [http://www.utoole.com/The-Adapter-and-3-Jaw-Chuck-for-Mounting-on-a-10-Rotary-Table_p_52.html 8" 3 Jaw Chuck and <s>adapter plate</s> for Rotary Table] | ||
* <s>[https://www.ebay.com/itm/New-List-Sale-5C-Collet-Chuck-With-Semi-finished-Adp-1-3-4-x-8-Thread/272966351763 5C Collet Chuck and Adapter]</s> | * <s>[https://www.ebay.com/itm/New-List-Sale-5C-Collet-Chuck-With-Semi-finished-Adp-1-3-4-x-8-Thread/272966351763 5C Collet Chuck and Adapter]</s> | ||
* [https://www.dzsalesllc.com/4-inch-precision-vise-p/100-vise.htm 4" Precision Tool Vise] | * [https://www.dzsalesllc.com/4-inch-precision-vise-p/100-vise.htm 4" Precision Tool Vise] | ||
Revision as of 15:56, 26 June 2020
Status: Large Vertical bandsaw still needs attention. We need to wire up the motor to a VFD (Andrew has stated that we can barrow the one from the 2 x 60" belt sander) to test the motor. If test is successful, Motor has been tested and is good to go, we need to reinstall the motor, clean up the bandsaw, remount the yoke and the table and get it prepped for a 3-phase power drop.
CNC Enclosure is now in place, work on the CNC will proceed soon. A new X axis ballscrew needs to be purchased and then some milling needs to done on the base, the saddle and bullnut mount made. Ballscrew has been ordered and received. Base has been milled. Saddle has been milled for the ballnut and a mount has been made. Need to mill oil groves in saddle and drill oil ports. Table may need some material taken off the bottom for clearance. The column spacer and head spacer needs to be milled out too.
Wishlist:
The existing stand is too large and bulky for the Mill. It's taking up way to much space. A smaller stand like this would work better for the Mill. $161.24 + 43.56 shipping
We'll mount the Mini-lathe to this toolbox. The existing medical rolling cabinet is too large and bulky, drawers on both ends confusing, and it's too low to the ground. $184.00 + Tax
10" Rotary Table with Tail Stock & Index Plates- 8" 3 Jaw Chuck and
adapter platefor Rotary Table 5C Collet Chuck and Adapter- 4" Precision Tool Vise
- Kant Twist Clamps (1" and 2")
Spindexer5C Collet Block Set5-C Collet Set (Imperial and Metric)1/2" Indexable Carbide TurningSlotted Angle Plate 9x7x6"Slotted Angle Plate 6x5x4-1/2"