COVID19 Response: Difference between revisions
(→Files) |
(→Files) |
||
| Line 35: | Line 35: | ||
|'''3D Printed Part''' | |'''3D Printed Part''' | ||
| | | | ||
Prusa Pro/RC4 for newer builds: | |||
[[Media:Prusa RC3 PETG single.stl|PETG]], | :[[Media:Prusa PRO 1x2.stl|PLA 1x2]], | ||
[[Media:Prusa RC3 ABS single.stl|ABS]], | |||
[[Media:Prusa RC3 ASA single.stl|ASA]], | RC3 (kept for '''legacy''' support reasons: you probably want the above files instead) Single in a variety of materials: | ||
[[Media:Prusa RC3 PC single.stl|PC]], | :[[Media:Prusa RC3 PETG single.stl|PETG]], | ||
[[Media:Prusa RC3 PLA single.stl|PLA]], | :[[Media:Prusa RC3 ABS single.stl|ABS]], | ||
[[Media:Prusa RC3 Nylon single.stl|Nylon]] | :[[Media:Prusa RC3 ASA single.stl|ASA]], | ||
:[[Media:Prusa RC3 PC single.stl|PC]], | |||
:[[Media:Prusa RC3 PLA single.stl|PLA]], | |||
:[[Media:Prusa RC3 Nylon single.stl|Nylon]] | |||
RC3 (kept for '''legacy''' support reasons: you probably want the above files instead) PLA stacks: | |||
:[[Media:Prusa RC3 PLA 1x2.stl|2]], | |||
:[[Media:Prusa RC3 PLA 1x3.stl|3]], | |||
:[[Media:Prusa RC3 PLA 1x4.stl|4]], | |||
:[[Media:Prusa RC3 PLA 1x5.stl|5]], | |||
:[[Media:Prusa RC3 PLA 1x6.stl|6]], | |||
:[[Media:Prusa RC3 PLA 1x7.stl|7]], | |||
:[[Media:Prusa RC3 PLA 1x8.stl|8]] | |||
|- | |- | ||
Latest revision as of 15:43, 12 August 2020
Overview
Knox Makers is organizing efforts to create and provide protective equipment and support to our local health community.
Face Shields
A face shield to be worn by medical workers.
Our design is based on the Prusa Face Shield with alterations made in response to feedback from UT Emergency Department.
It involves a 3d printed part printed part, a laser cut part, and button hole elastic.
Materials
| 3D Printed | PETG, ABS, ASA, PLA, PC, Nylon (please print the corresponding file) |
| Laser Cut | An acetate plastic
7mil to 20mil (thicker is preferred) |
Page for 3D printing suggestions
Files
| Laser Part | svg |
| 3D Printed Part |
Prusa Pro/RC4 for newer builds: RC3 (kept for legacy support reasons: you probably want the above files instead) Single in a variety of materials: RC3 (kept for legacy support reasons: you probably want the above files instead) PLA stacks:
|
Bias Tape Makers
Bias tape makers help make the pleats in the fabric masks.
They can be 3d printed and are helpful to the community making these masks.
Files
5cm (wings) (stl)
5cm (stl)
4cm (wings) (stl)
4cm (stl)
Fabric Masks
Fabric masks are meant to protect from the spread of droplets from the wearer's mouth and nose.
These are currently being recommended for everyone and not just health workers.
Surgical Mask Straps
The surgical mask straps hold the elastic that normally is held by a health worker's ears.
It helps save the irritation caused by prolonged usage.
Files
Suraky's Remix (stl)