Laser Cutter Settings
This page needs to describe our inkscape plugin. We should think about listing out the values that we have as useful starting points for anyone wanting to try further experimentation.
Link back to Laser Cutter
Table of Values by Material
After testing some sample materials, these values were selected based on giving the best visual impression. That includes minimal charring and smoking, best accuracy, and are ultimately entirely subjective. Use these as starting points for your experiments. See below for an explanation of what the parameters mean.
| Material | Action | Feed Rate | Laser Power |
|---|---|---|---|
| 3mm Plywood | Cut | F400 | Q0.4 |
| 3mm Plywood | Engrave Heavy | F400 | Q0.14 |
| 3mm Plywood | Engrave Light | F400 | Q0.13 |
| 6mm Plywood | Cut | F400 | Q0.6 |
| 6mm Plywood | Engrave Heavy | F400 | Q0.14 |
| 6mm Plywood | Engrave Light | F400 | Q0.13 |
| 3mm Acrylic | Cut | F400 | Q0.4 |
| 3mm Acrylic | Engrave Heavy | F400 | Q0.152 |
| 3mm Acrylic | Engrave Light | F1000 | Q0.164 |
| 6mm Acrylic | Cut | F200 | Q0.6 |
| 6mm Acrylic | Engrave Heavy | F1000 | Q0.2 |
| 6mm Acrylic | Engrave Light | F1500 | Q0.12 |
| Paper | Cut | F500 | Q0.165 |
| Paper | Engrave Heavy | F1500 | Q0.128 |
| Paper | Engrave Light (Perforate) | F1000 | Q0.2 |
| Cardboard | Cut | F1000 | Q0.5 |
| Cardboard | Engrave Heavy | F1000 | Q0.14 |
| Cardboard | Engrave Light | F400 | Q0.13 |
Note: These are the values used by default in the version 0.13 of the Inkscape Plugin. All values use S10000, except for Paper, Engrave Light. It uses S1 to perforate instead of mark.
GCode
The laser cutter operates using LinuxCNC, and uses 3 specific commands to modify the type of cut made by the laser.
M68 Command
The M68 command is used by LinuxCNC to specify an analog output. Our laser is configured to use the E0 output and the Q parameter to modulate the laser power when cutting in automatic mode. Based on previous testing a Q value less than 0.12 are insufficient to even brown paper at most speeds. Values greater than 0.6 will cause the laser to exceed its maximum current. For than reason, this parameter is internally limited to 0.6. Putting in larger values will not have any effect.
Samples:
- M68 E0 Q0.125 - This would represent a very low power beam. Speeds would have to be very low to mark anything other than paper.
- M68 E0 Q0.6 - This is the maximum laser power. At low speeds this will cut through most materials on our approved materials list.
F Parameter
The F parameter specifies the feed rate for all following moves. This would be the linear movement speed of the lens carriage. The speed effects the amount of cutting that the laser beam does to the material that it moves over. At a given laser power, a slower speed will cut deeper or burn more, and a faster speed will cut shallower or burn less. Testing has shown that above F1500, the precision of the laser carriage deteriorates to the point of visual artifacts being present in the work.
S Parameter
The S parameter specifies the number of pulses per unit of length. In any case that you want a continuous cut or etched line, this should be specified as S10000. The Inkscape Plugin uses S10000 as the default on all cases, except light engraving of paper. For light engraving of paper, a value of S1 is chosen so that it perforates instead of creating a continuous cut.